51³Ô¹Ïapp

Report all emergencies -Ìý9385 6666

• State your name
• Location of the incident, building/floor and room number.
• What the emergency is: fire, bomb, gas, chemical etc

Stay calm and advise others

• Security
• Your work mates
• Your supervisor
• Other students

First aid officers

Phil Allen, Room 318/347,Ìý9385 4003

Gabriel Graterol Nisi, Room 120

Zoe George, Room LG07,Ìý9348 2295

Lucy Chen, Room G15,Ìý9385 5509

Jolanta Witkowska, Room 105, 9385 4009

Olivia Huang, Room 103,Ìý9385 4001

Location of nearest first aid box

• First Floor: School Office room 103.

Chief and Deputy Chief Wardens

• Zhenyu Liu: Room G15, PhoneÌý55508
• Roy Zeng: Room G15, PhoneÌý55507

Emergency evacuation proceduresÌýWhat should you do if the alarm sounds while you are in the Electrical Engineering Building?

1. On hearing the alarm sounding as : beeep beeep beeep beeep
2. Prepare to evacuate and follow instructions from any Public Announcements or Emergency Team members. Save files, turn off equipment and remain calm.
3. On hearing the alarm sounding as: whooop whooop whooop whooop
4. Evacuate the building immediately. Leave the building via the nearest safe emergency exit
5. Do not use the lifts.
6. Proceed as directed to the Evacuation Assembly Area. This is at the QUADRANGLE LAWN to the west of the building.
7. Remain in the assembly area until notified to return to the building.

You do not need to deal with WHS matters alone. Talk to someone. The following staff are available to provide advice about the specific WHS hazards listed.

• Ergonomics & Manual Handling:ÌýEmilio Saliba
• Dangerous goods/hazardous substances: Lucy Chen Note that NO dangerous goods/hazardous substances may be brought into the School without having safe storage and transport arrangements approved by Lucy first.
• High voltages:ÌýZhenyu LiuÌý
• Lasers:ÌýLucy ChenÌýNote that NO work with a class 3B or 4 laser may be undertaken in the School before having the risk assessment approved by Lucy.
• Radio frequency radiation:ÌýSimon MaunderÌýandÌýYixuan Xie

For information on other hazards, pleaseÌýaccess the central .

In addition, the School's HSE Advisor,ÌýEmilio Saliba, is available to help with all Health and Safety related questions.

Each School has specific rules about conduct in laboratories to promote safety at work.

The following general rules apply to ALL laboratories in the School of Electrical Engineering & Telecommunications:

1. All users must undergoÌý, agree to comply with Laboratory rules, and observe ergonomic arrangements for their workspaces.
2. No bare feet or exposed/open footwear are permitted ().
3. Food and drink are not to be consumed at any time in the laboratories.
4. Under no circumstance is the 240 V, 50Hz mains power to be used for any purpose other than that approved by the School. Only authorised personnel are allowed to alter power connections (50 V above) or connect any equipment to mains power.
5. Tampering with or removal of any laboratory equipment is strictly forbidden.
6. Data network connections should not be altered. Personal equipment may not be connected to the School data network without first obtaining permission.
7. Personal mobile phones are not to be operated at any time within a laboratory.
8. Users are always expected to conduct themselves in a reserved and professional manner. All noise should be kept to a minimum.
9. All bags should be stored out of walkways.
10. When finished, all users should clean and tidy their workstations, shut-down the PC, return all leads, and turn out the lights (if last to leave).
11. Faulty equipment and any other concerns should be reported to laboratory staff who may not otherwise be aware of the problem.
12. Users must also comply with UNSW’s policies & procedures aboutÌý

Research Laboratory Users:

Users of EE&T research laboratories who have any form of equipment setup (for fabrication, experiments, measurements or other) must display a filled-in Activity Detail Sheet next to their setup (Activity Detail Sheet docx,ÌýActivity Detail Sheet pdf).

Safe work procedures (SWP) and Risk Management Forms (RMF) describe how a particular task should be safely undertaken.

SWPs and RMFs have been developed for a number of different tasks performed in the various laboratories around the School. It is imperative that staff and students read, sign, and follow these instructions which are located near to the relevant equipment in the laboratories and/or onÌý. If you cannot locate the relevant SWP or RMF for the equipment you wish to use or the activity you wish to carry out, please contact the Area Supervisor before operating the equipment.

The University's Online Safety Management System ( must be used to complete SWPs (for equipment) or RMFs (for activities).

Before considering the purchase of a new piece of equipment, theÌýHS633a Pre-Purchase Checklist for EquipmentÌýmust be completed and submitted to the Supervisor of the area where that equipment will be used, and a new SWP or RMF may be required for it.

Before considering the purchase of a new chemical or Hazardous material, theÌýHS633b pre-purchase form for hazardous materialsÌýmust be completed and submitted to the Supervisor of the area where that equipment will be used, and a new SWP or RMF may be required for it.

All new SWPs should be submitted directly to your Academic Supervisor, or the area supervisor for approval online before work begins.

All SWPs should be regularly reviewed and updated as new activities are undertaken.

Engineering laboratories are potentially dangerous places. Rules regulating behaviour apply in the photonics laboratories, just as they do elsewhere in the School whose generic rules are displayed elsewhere.Ìý

You will appreciate that there can be NO tolerance of unsafe behaviour. We must exclude any student who does not comply with laboratory safety requirements (including the wearing of appropriate shoes).

The following extra rules apply to the relevant hazards:

Broken Glass

• All fibre off-cuts must be disposed of correctly, into the yellow containers provided. Be aware that fragments of glass may be present on any surface (floors, bench-tops, shelves, etc) in the rooms, so look before resting your hand, elbow, etc.

LasersÌý-ÌýLaser radiation can damage your eyes, even when invisible.

• Never look into an operating laser or the end of an optical fibre.
• Always ensure that your laser-beams are terminated by a suitable non-reflective surface. Check this is the case.
• Be careful to prevent accidental reflections & refractions that may send the laser-beam in unintended directions or accidentally pointing an optical fibre at someone.
• Always keep any metallic objects (e.g. watches, rings, pens) out of a laser-beam.
• Whenever possible, arrange the experiment so that you are not working with lasers at eye-height.
• Unattended lasers must be switched off.
• Lasers of class 3B or 4 (which are never eye-safe) must not be used without special permission and suitable extra arrangements being in place.

Rotating Machinery

• Always ensure that fingers and any loose materials such as a sleeves and hair are kept well away from moving parts.

Hot Surfaces

• Be careful not to touch any metal surfaces heated by white light sources.

Please visit the link below for information about lab and building access at the School of EE&T.

School's Health & Safety Committee Members

Head of School

Jinhong Yuan

Chair of the School's Health & Safety Committee:

Torsten Lehmann

School WHSÌýAdvisor:

Emilio Saliba

Staff Representatives:

Zhenyu Liu,ÌýSimon Maunder,ÌýRoy Zeng,ÌýMatthew Boreland, Clay Chu, Elias Aboutanios, Gabriel Nisi, Lucy Chen

Student representatives:

Undergraduate - TBA

Postgraduate - TBA